BTuned Performance

Q50 with full downpipes and 3 inch catback paired with boosted6auto Shorty Intakes & Heat exchanger
With my EcuTek Technologies Ltd calibration we put down 📈452whp & 502wtq🦍
••••
We have the tools and knowledge to get your G/Z/Q/GTR where you want it to be with parts, fabrication, installs and tuning all done in house!
•••••
Message us on any of our social media accounts
📲or💬 407.334.3419
📧[email protected]

VQ gainzzz 💪🏽

08 G37 coupe with Z1 Motorsports, Inc. 3 inch intakes, Berk High Flow 🐱 and my EcuTek Technologies Ltd calibration.
📈324whp & 262wtq🦍
••••
We have the tools and knowledge to get your G/Z/Q/GTR where you want it to be with parts, fabrication, installs and tuning all done in house!
•••••
Message us on any of our social media accounts
📲or💬 407.334.3419
📧[email protected]

08 G37 coupe with Z1 Motorsports, Inc. 3 inch intakes, Berk High Flow 🐱 and my EcuTek Technologies Ltd calibration.
📈324whp & 262wtq🦍
••••
We have the tools and knowledge to get your G/Z/Q/GTR where you want it to be with parts, fabrication, installs and tuning all done in house!
•••••
Message us on any of our social media accounts
📲or💬 407.334.3419
📧[email protected]

With Z1 Motorsports, Inc. Intakes and our 3” BTP Catback mated to our prototype resonated lowers, this RZ34 put down
📈434Whp & 467wtq🦍
••••
We have the tools and knowledge to get your G/Z/Q/GTR where you want it to be with parts, fabrication, installs and tuning all done in house!
•••••
Message us on any of our social media accounts
📲or💬 407.334.3419
📧[email protected]

Z1 Motorsports, Inc.VRX70s, SPOOL Performance injectors, E60 and exhaust dumps putting down a solid 📈732whp & 591wtq🦍
This car picked up 40whp switching from home made 3 inch intakes to boosted6auto Longtube intakes and NO changes to the tune target boost or timing.
••••
We have the tools and knowledge to get your G/Z/Q/GTR where you want it to be with parts, fabrication, installs and tuning all done in house!
•••••
Message us on any of our social media accounts
📲or💬 407.334.3419
📧[email protected]

This Q50 sporting a full 3 inch setup with boosted6auto shorty intakes laid down a strong power band with our typical formula. Using EcuTek Technologies Ltd software we dialed this car in and it responded perfectly with clean, strong and smooth power band.
•••••
We have the tools and knowledge to get your G/Z/Q/GTR where you want it to be with parts, fabrication, installs and tuning all done in house!
•••••
Message us on any of our social media accounts
📲or💬 407.334.3419
📧[email protected]

Photos of our Custom exhaust on these RZ34 🫡
Full 304 stainless steel in 3 inch with the large Xpipe
Using stainless_bros products not only can you rest assured you are getting the highest quality materials, they are made in house, on your car, for the sound you want.
••••
We don’t only make exhaust, we can make 3” cold air intakes for the RZ34, 370z, 350z and anything in between. Want to add boost to your NA car? We got you covered with top mounts, mid mounts and even twin turbo setups. Full frame VR30 turbos😏
Let us help you accomplish your fabrication dream

VRX80s on 93 octane putting down some good power. Wonder what she will make on E85 with port injection 👀

This G35 coupe came in for a rear main seal replacement and we found a lot more than what we thought. Between the oil leaking and the clutch fibers coming off the clutch disk, there was an absolute mess in the trans. Among a few other red flags we found while doing the job like rtv in the pickup tube, broken motor mount and non OEM parts being used before. This owner can rest assured now that his cars in good shape. With new OEM parts and upgraded mounts from Z1 Motorsports, Inc., she’s all cleaned up and ready for the next adventure!